Flat Lapping Machine
Lapping machine 26 inch

Lapping machine 26 inch

We're here to help Easy ways to get the answers you need.
Contact Now
  • Lapping machine 26 inch
  • Lapping machine 26 inch
  • Lapping machine 26 inch
  • Lapping machine 26 inch

 
1.Application :
This machine is designed for lapping and polishing of high-precision flat surface. Such as mechanical
seal rings, new ceramic grinding plates, hydraulic oil pump accessories, etc. By using different lapping
 discs and polishing liquid, aluminum, copper, iron, carbide, engineering plastic, alumina and silicon 
 carbide can also be lapped.
 
2.Structure & Features:
Features: Equipped With pneumatic cylinder,easy adjustment and operation; Also equipped with an 
automatic & timed lapping fluid  adding device; Adapting three-phase converter to achieve variable
 speed change;Using worm gear reducer. Advantages: Small size, high efficiency, stable operation, low
 noise,long life. It is  suitable choice for lapping and polishing medium-sized seal rings. The polishing 
 disc diameter φ650, which can lap rings with diameter of φ240mm  maximum.
 
3.Main Technical Parameters :
1. Motor: 2.2KW ;1430 rpm (with 3kw converter)
2. Polishing plate size: 650mm x 150mm (Outer diameter x inner diameter)
3. The maximum diameter can be lapped: 240mm
4. The thinnest  thickness can be lapped: 1mm
5. Flatness(after being polished): 0.0006mm. Roughness: Ra 0.05μm
6.Machine Dimension: 900mm x 1100mm x 1900mm (length x width x height)
7.Machine Weight: 1600Kg
 
4.Installation :
Placed on a flat solid concrete floor, calibrated with a spirit level
 
5.Operation and precautions :
1.Clean the worktable , dead wights and conditioning rings.
2.Clean the workpiece to avoid inclusion of debris.
3.Discharge the workpiece in 3 conditioning rings, leaving Ø30mm-Ø60mm space in the middle. 
    Switch on the air supply and set the total air inlet pressure to 0.3-0.4Mpa. Pressurization and 
    set the air pressure to 0.05-0.2 Mpa (pressurizing 0.1 Mpa is equivalent to applying 20 kg 
     pressure to the workpiece). The lapping  fluid pressure is set to 0.02-0.04 Mpa.
4.Turn on the power, start the machine, set a reasonable polishing time. Set the time for
    adding the polishing liquid (usually 5 seconds spraying every 1 minute).
5. After work, be sure to take the conditioning ring and the workpiece out of the machine. It is 
    forbidden to keep them on the lapping plate overnight to prevent rust from corroding the 
    grinding disc and damage the converter when restart.
6. The machine tool should be always kept clean and tidy . Clean inspection should be conducted
     when the shift is over. Before the holiday, countertops and some other major parts should 
      be protected against rust.
7. The machine should be operated by skilled personnel only.
8. Only professional maintenance personnel can carry out maintenance, and it is strictly forbidden
     to install and disassemble the machine and change any spare parts of the machine.
6.Refueling lubrication:
  1. Use 46# gear oil for turbine box, change oil once after the maching is running for 100 hours. 
      Afterward,  change the oil every 6 months. The oil level should be maintained at 1/3 or more.
 
  7.Trim polishing plate:
    After the disc is worn out, it must be machined on the lathe and then trimmed. The emery or white
    steel jade sand, brown steel jade sand, and  green silicon carbide sand are used for the repair. Sand 
    particle size generally between 100-200 meshes. Trim the polishing plate with a trimming ring. When 
    the polishing plate is convex, the trimming ring moves towards the center; Otherwise it moves 
    outwards; If it is wavy, then one ring moves towards the center, one ring moves to the outside and
    the other ring remains in place. The trimming ring movement generally does not exceed 5mm.
 
   8.Defect analysis and troubleshooting
    Possible Problem:Scratch 
    Possible Causes:1.Scraps of the workpiece. 2.Coarse sand is mixed in polishing liquid.   
   Solutions: 1.Clean workpiece 2. Change polishing liquid 3. Trim polishing plate
   Possible Problems:Not Shinning enough
   Possible Causes:1.Quality of Abrasive paste is poor 2.Workpiece is green. 3.Plate line on
   Table-board is shallow 4. Polishing time is too short
   Solutions:1.Change abrasive paste 2.Change workpiece 3.Adding plate line 4.Set an
    reasonable polishing time
   Possible Problems:Poor flatness 
   Possible Causes:1.Table board is uneven 2.Polishing time is too short. 
   Solutions:Trim polishing plate 2.Prolong Polishign time
   Possible Problems:Machine can not be started 
   Possible Causes:phase error of motor 
   Solutions:Change the connection phase
  9.Accessories:
  1) 3 pieces of conditioning rings.             2) 6 pieces of Isolation panels.               3) 1 piece of hex wrench.
 
Weight & Dimensions:
GROSS WEIGHT – 686 KGS APPROX 
DIMENSIONS :  L 111.8 x W 111.8 x H 106.7 CMS APPROX


 How to choice the ideal polish and lapping machine ?

As you are already aware, machines for lapping/polishing mechanical seals basically divided into Soft Lapping / Soft polishing and Hard Lapping / Hard Polishing.
 
In Mechanical seals, you have seals of SS, Hardened steel, Coated like Stellite and some non-ferrous applications also. The lapping of these materials are usually by Abrasive slurry and polishing usually by 4/0 Emery sheet by hand, else with polishing pads and polishing slurries.
 
Hard lapping / Polishing – Usually referred to the use of Synthetic or Natural Diamond as abrasive. And again not all lapping or polishing application calls for the same abrasive.
 
And the selection of Vehicle or lapping media is very important.
 
For Carbon, SiC, TiC and Ceramic - the plates should be different, i.e. 3 plates, but again Ceramic if lapping and polishing is to be done, m/c's should be separate and plates separate for rough polishing and fine polishing.
 
With Paraflat, we have never given a quote to any customer off-hand, we always insist on knowing the details of the part/s to be lapped or polished, the previous operation, output quantity planned per shift of 8 hours, part drawings, etc. This practice helps us make a proper recommendation.
 
* For other lap plates of Copper, etc, if required, the prices will be different.
* Kindly also confirm the power supply details. 


  
Hence it is always better if the user/client’s requirement is known before hand to make a correct recommendation, else lot of time is spent making corrections and clarifications.
 

Get Price And Support

Simply complete the form below, click submit, you will get the price list and a representative will contact you within one business day. Please also feel free to contact us by email or phone.

Name: *
Country: *
Company:
Phone: *
E-mail: *
Message: *
Code: *
Contact Form
CONTACT US
  • TDS Fluid Industries, LLC 7646 Pebble Drive Fort Worth, Texas 76118
  • TDS Fluid lndustries LLC. in TX,USA
  • Tel:1-817-616-3296(English)1-8882818150(Spanish)
  • TDS Fluid IndusTrIes Australia Pty Ltd. in Sydney,Australia
  • Tel:61-2-87640203(English)61-2-97081455(Spanish)
  • Shanghai TDS Industry Imp & Exp Corporation
  • Tel:021-60401444(English) 021-60190533(Spanish)
  • Email:Info@TDSFluid.com
Copyright symbol ©